How to Program Remotes for HONDA Civic 2018 using AUTEL IM608

Instruction: How to program remotes for HONDA CIVIC 2018 by Autel IM608 programmer.

Go to Autel IM608 IMMO software

AUTEL-im608-honda-civic-remote-program- (1)

Accept the agreement

AUTEL-im608-honda-civic-remote-program- (2)

Honda – Manual selection – Civic – Touch tone smart card

AUTEL-im608-honda-civic-remote-program- (3)

AUTEL-im608-honda-civic-remote-program- (4)

AUTEL-im608-honda-civic-remote-program- (5)

AUTEL-im608-honda-civic-remote-program- (6)

Immo status scan

AUTEL-im608-honda-civic-remote-program- (7)

Is the ignition on by pressing the start button twice

AUTEL-im608-honda-civic-remote-program- (8)

No fault

AUTEL-im608-honda-civic-remote-program- (9)
AUTEL-im608-honda-civic-remote-program- (10)
AUTEL-im608-honda-civic-remote-program- (11)

Autel is gonna to add a smart key

AUTEL-im608-honda-civic-remote-program- (12)

Registration condition:

there are no DTCs
there must be one registered keyless remote
one keyless remote that is capable of starting the engine must be in the vehicle
the ignition switch must be turned on (II) using the keyless remote (the ignition key must not be used)

Notes when registering

Ensure the following to reduce noise as much as possible during keyless remote registration:

Turn off all electrical devices (e.g. navigation and audio systems) Separate the diagnostic tool from the keyless remote as much as possible. Close all doors, windows and sunroofs.

AUTEL-im608-honda-civic-remote-program- (13)

Please turn the ignition switch off

(Dont press the foot brake and press the engine start/stop button)

Pls wait for the ECU to stablise

Remove all other keyless access remotes from the vehicle

Pls take on registered keyless access remote into the vehicle

AUTEL-im608-honda-civic-remote-program- (14)

Please turn the ignition switch on

(Dont press the foot brake and press the engine start/stop button twice)

Vehicle condition checking…

Take all original keyless access remotes out of the vhicle

AUTEL-im608-honda-civic-remote-program- (15)

Take a new keyless access remote into the vehicle

This keyless access remote is now registered

AUTEL-im608-honda-civic-remote-program- (16)

Please turn the ignition switch off

(Dont press the foot brake and press the engine start/stop button)

Pls wait for the ECU to stablise

Please turn the ignition switch on

(Dont press the foot brake and press the engine start/stop button twice)

Are both the keyless access and immobilizer indicator lights turned off?

AUTEL-im608-honda-civic-remote-program- (17)

Please turn the ignition switch off

(Dont press the foot brake and press the engine start/stop button)

Pls wait for the ECU to stablise

Please turn the ignition switch on

(Dont press the foot brake and press the engine start/stop button twice)

The registration is completed

Please turn the ignition switch off

(Dont press the foot brake and press the engine start/stop button)

AUTEL-im608-honda-civic-remote-program- (18)

Pls wait for the ECU to stablise

Check all keyless access remotes to ensure each will start the engine

Check all keyless access remotes to sure each will lock and unlock doors

Please turn the ignition switch on

(Dont press the foot brake and press the engine start/stop button twice)

AUTEL-im608-honda-civic-remote-program- (19)

Immo status scan

AUTEL-im608-honda-civic-remote-program- (20)
AUTEL-im608-honda-civic-remote-program- (21)
AUTEL-im608-honda-civic-remote-program- (22)
AUTEL-im608-honda-civic-remote-program- (23)

Job’s done!

Be the first to comment

Leave a Reply

Your email address will not be published.


*